(navigation image)
Home American Libraries | Canadian Libraries | Universal Library | Community Texts | Project Gutenberg | Children's Library | Biodiversity Heritage Library | Additional Collections
Search: Advanced Search
Anonymous User (login or join us)
Upload
See other formats

Full text of "John_Deere_11A_12A_Combines_Reel_Attachment"



This manual 

contains correct 

information 

regarding 

operation, 

lubrication, 

setting up, and 

parts list. 




OPERATORS 
MANUAL 



No. OM-H19-1248 



> 



JOHN DEERE 

RATCHET TYPE ROPE- 
CONTROLLED REEL 
ATTACHMENT 

FOR 

£**** JOHN DEERE 
Nos. 11 -A and 12- A 
COMBINES 



llOab 



1 



For the best service see your 
JOHN DEERE DEALER 

Use Only Genuine John Deere Parts 



INSTRUCTIONS FOR ADJUSTING AND 

OPERATING JOHN DEERE RATCHET 

TYPE ROPE-CONTROLLED REEL 

ATTACHMENT 



: : 



1 






This attachment permits the operator to raise or lower the reel from 
the tractor without leaving the tractor seat. 

Before operating reel, lubricate racks so reel will slide up and down 
smoothly. See Lubrication Chart on following page. 

To raise the reel, pull on rope until j^ng^eT^'' Figure 1, com- 
pletes a full stroke. Each .complete stroke raises reel approximately 1-1/2 
inches. To lower thTreel, pull on rope until raising lever has completed 
a full stroke, then slacken rope enough to allow raising pawl "B," Figure 1, 
to disengage from raising gear; pull on rope until raising pawl comes in 
contact with lock pawl "C," Figure 1, disengaging it from the raising 
gear, thereby freeing reel and allowing it to slide down. By pulling hard 

on rope, a braking action can be applied 
to prevent reel from dropping too 
fast. This causes lock paw^C^Figure 
1, to exert pressure on brakeShoe 
angle "D," Figure 1, which, in turn, 
binds on right-hand rack. By releasing 
rope quickly the lock pawl will again 
contact raising gear and stop the 
downward movement of reel. 

If operator wishes to lower reel by 
hand, place four fingers under raising 
lever "A," Figure 1, and press on 
raising pawl "B," Figure 1, with thumb, 
pull up on lever until raising pawl 
comes in contact with lock pawl "C," 
Figure 1. This will allow reel to slide 
down. 

To move reel forward or back, loosen 
lock bolt "A," Figure 2, and lock handle 
"B," Figure 5. Tighten after each ad- 
Figure l justment. 




SETTING UP JOHN DEERE RATCHET 

TYPE ROPE-CONTROLLED 

REEL ATTACHMENT 

SHIPPING PACKAGES 

14022 HH Reel Pipe for No. 11 -A Combine 

14023 HH Reel Pipe for No. 12-A Combine 

14024 HH Reel Racks and Lift Parts 
*11832 HH Reel Arm Reinforcing Plates 

* This package, which consists of two P 32384 H Reel Arm Reinforcing 
Plates and Bolts for attaching, is needed only when installing this attach- 
ment on John Deere No. 11-A Combine prior to Serial No. 11-7151 or 
John Deere No. 12-A Combine prior to Serial No. 12-13955. Discard your 
old square reel rehjfbFerng^plates. Order direct from your John Deere 
dealer. — *-"" 



If this attachment is to be in- 
stalled on a machine in the field, it 
is necessary to remove reel complete 
with support parts. Remove reel 
arms, slats and reinforcing plates 
from reel pipe. These will be used 
with the new adjustable reel. 

1. (Figure 2) Bolt reel pivot angle 
and brace to grain tank front support 
angle, left-hand, as shown — on sacker 
machine bolt to sacker platform front 
support angle, left-hand. 

2. (Figure 2) Bolt round brace for 
pivot angle to axle tube. 

3. (Figure 3) Bolt reel support 
rack, right-hand, to bracket at right- 
hand end of platform sill. Bolt reel 
support rack brace angle to inside of 
reel pipe bracket, right-hand. NOTE: 
Be sure trunnions are in place in reel 

support rack and brace angle — longest one goes into reel support rack. 

4. (Figures 3 and 4) Remove cotter, pin, raising gear, Zerk fitting, 
slip clutch, slip clutch spring, and slip clutch spring clamp from right-hand 
end of reel shaft. Slide reel arm reinforcing plate, right-hand, "A," Figure 3, 
onto reel shaft. Reinstall slip clutch spring clamp, slip clutch spring and 
slide reel driven sprocket onto reel shaft. Slide slip clutch onto reel shaft, 




Figure 2 



2 



securing with Woodruff key found in bag of parts. Screw Zerk fitting 
through slip clutch into reel pipe. Place thrust washer against slip clutch, 
secure with snap ring (snap ring is in bag of parts). Next install PK 442 H 
raising lever "B," Figure 3. Slide PK 445 H raising gear onto reel shaft, 
fasten to shaft with pin. Secure pin with cotters. Assemble brake shoe angle 
and PK 370 H lock pawl onto pivot pin in PK 441 H latch support bracket 
"C," Figure 3. Assemble PK 441 H onto reel support rack, right-hand, 
and bolt to PK 440 H shown at "C," Figure 4. Slide reel shaft through 




latch support assembly. Block up left-hand end of reel pipe while doing. 
Slide PK 372 H, right-hand half of raising lever "D," Figure 3, onto shaft 
and bolt to PK 442 H raising lever. 

5. (Figures 2, 3 and 4) Slide rear end of reel adjusting pipe, rign^w^ 
hand, into socket on pivot angle and secure by tightening lock bolt "A," 
Figure 2. Secure front end of pipe to latch support assembly as shown in 
Figures 3 and 4. 



6. (Figure 5) Bolt 
P 40990 H* clamp brack- 
et for reel adjusting pipe 
left-hand, to left-hand 
side of machine as shown. 

7. (Figure 5) Remove 
cotter, pin, rack, gear, 
rack guide and reel shaft 
shield, washers and reel 
shaft shield collar from 
left-hand end of reel 
shaft. Slide reel arm re- 
inforcing plate, left-hand, 
"A," Figure 5, onto reel 
shaft. Replace reel shaft 
shield collar (bolts to left- 
hand reinforcing plate), 
reel shaft shield, and rack- 
guide. 

8. (Figure 5) Loosen 
handle "B," Figure 5, on 
pipe clamp and insert 

Figure 4 reel adjusting pipe, left- 

hand. Tighten handle. 
Bolt other end of adjusting pipe to rack guide, left-hand. 

9. (Figure 5) Slide reel support rack, left-hand, through rack guide 
and bolt to platform sill, as shown. 







10. (Figure 5) Pin and cotter PK 669 H gear to left-hand end of reel 
shaft, being sure that reel pipe is level and gears are in corresponding 
teeth on both racks. 



* When using Ratchet Type Rope-Controlled Reel on a Flax Roll Combine, remove this part 
from PK 447 H Pipe Clamp and attach clamp directly to flax roll main drive chainjshield. 



#> 




11. (Figures 3 and 4) Assemble PK 446 H raising pawl in raising level 
with pivot pin. Cotter at both ends. Hook small spring to raising pawl 
and to raising lever, as shown in Figure 4. 

12. (Figure 4) Assemble raising lever return spring (long coiled spring) 
as shown. 

13. (Figure 3) Assemble torsion spring onto PK 441 H. Latch bracket 
so pressure is placed on top of PK 370 H lock pawl. 

14. (Figure 3) Thread rope through pulley on upper end of right-hand 
rack and tie to lifting lever. 

15. Assemble reel arms and slats; also reel drive chain — see Setting- 
Up Manual OM-H4. 

16. Reel should be centered in platform. If not, loosen bolts "E," 
Figure 3, and move reel to left or right until centered. Tighten bolts. 




Figure S 



17. Raise and lower reel. If it binds on racks, remove left-hand gear, 
see "10," Figure 5, and raise or lower left-hand end of reel until it is free. 
Replace gear. When doing this be sure that raising pawl comes down far 
enough to take two teeth on raising gear. Adjust at set screw "F," Fig- 
ure 3. 



MEMORANDUM 



% 





lOT-r-^OlNOOWWOWfflCMN 
*- . O ■* i- r- lO 10 N- I s - 03 I s - •*• *J" ■* O <M 

>-Ot--*o i-cj-oo ro tj- ■* «*■ m oo 



(O 



CM 1^- h- 

oooo ro 



n-i 
coco 



I 
I Q. Q. -3 Q. Q. Q. D. 0.0.0.0.0.0. 



© o ffloiOT-cjn^inioNtofflOi-w 

f£Z i-i-CMCMCMCMCVICMCVICVICMCMMMCO 



mOCM-r-OO 
HO CO lOfO 
00IO <OCM 
CO CM 

Q.CQQ.O.Q. 



ro tj« in ion- 
co ooco coco 



CO 

6 









Sl- 



ow 
'is? 



c c 
o o 

<<, 

t- i- C C r- 

' — '^-'o o o 



>- o 

.5— to. 

c ® 9 s 

O 03 03 

I ■£ ID 

- J co 



CO 
ro 



•a 

o 
o 



J I 



^ *-.- 



Oj: w 

*" -M —J 

*S2..n 

03,- 



^ 2 CM 1— CJ 

O. O.C-C- n 

coco^^.S-^.r- 

.t; .t; .c .c ». ™ ^ © o 

3 StOtO 00 »~ „, 

<d » J; ~ >, a..— E > 

- o = ^-> Q.2-.S8 S50 &••= 

occcoco<>oo_o.aa*coco<o 



(3 CO 

— 03 
03 73 
O — 

QCc75 



oil rt 
>"- 03 

O 03 CD 
*-< 

— £ oJ5 

03 0-= 



?6 
,-Z 

™ C 
i£00 

1:6 



00 



00 



ft 

© — -s c 

COD- -J 



IIII IIIIII II I I 



000>'- , <fr-lOOO<DCV100CM'* , OON--.-N. 
+* . (O CO (O ^J- CT> t— (O CO <*■ N- * t— N- CM N- OJ 
|5 O WtD0OmN.tOC»C00O'tCO_rOinh»0O 

.P2 co 10 (on. in * to coin, col N-rs.o 

0.^- CO t-t- CO 00 »- t- CO CO 10 CM t- 

¥0.0-0 Q-Dl w ¥ qQl 
CLQ-<<-3Q.Q.<<Q.Ql Q.CL-3< 



Ol 

< 



II 

CMi-CJ 
CON- Tf 

N. 

CO 

Y. 

0-0. 



03 O 

orz 



■ cm 00 * in to n 00 en o^-cmcom- 



3 » 
03 *> 



c « 

II 

< a 
co in 
|g 
~« 

*S 

03 1- 

73M 

3 

11 

•*-> k 

o< 

43 IA 

a) a 

j2u5 

ag 

off 



Hit. 



W 




REEL RACK AND TILTING PIPE, R. 



H. 




Ref. 


Part 


No. 


No. 


1 


28H 1 72 H 


2 


P 26770 H 


3 


P 37479 H 


4 


P 37480 H 


5 


P 37477 H 


6 


P 37496 H 


7 


P 28709 H 


8 


J 3525 H 


9 


PK 444 H 


10 


AP 16543 H 


11 


P 37474 H 


12 


P 33266 H 



Trunnion 

Trunnion 

Angle Brace 

Reel Rack, R. H 

THting Pipe, R. H. 

Stop for Slide Brackets 

Lock Bolt 

Pivot Pin (3/8" x 2-1/2") 

Lock Bracket 

Upright Post 

Round Brace 

Flat Brace 




Ref. 
No. 

1 

2 

3 

4 

5 

6 

7 



Part 
No. 



Description 



P 37494 H Bracket for L. H. Rack 

28H 172 H Trunnion 

P 37058 H Reel Rack, L. H. 

P 40990 H Bracket on Combine (Not used on Flax T Roll Machines) 

PK 447 H Lock Bolt Bracket 

P 28709 H Lock Bolt 

P 37476 H Tilting Pipe, L. H. 




10 



V 



■ 



# 



\ 



- 



11 



FOR GENUINE JOHN DEERE 




AND FACTORY-CONTROLLED 




the same pa« er > yoU mone^ ^ gh quaU ty 1 

throughout n take adva & speC ial se ^\ noW your 

Vou'U also find i gg when you neea J . CJ w ho knjJ^ olk 
by Y y °our John Deere deal^ ^jjrf*^ doing ? -\ aCtio a 

f h y n Deere equP- ^ ,. agtf yQU comP^^iuon. 



on 











Farm Accidents Can Be Prevented 

uritk t fousi Jlelp, 



NO accident prevention program can be successful with- 
out the whole-hearted cooperation of the person who 
is directly responsible for the operation of equipment. 

To read accident reports from all over the Country is 
to be convinced that a large number of accidents can be 
prevented only by the operator anticipating the result be- 
fore the accident is caused and doing something about it. 
No power-driven equipment, whether it be transportation 
or processing, whether it be on the highway, in the harvest 
field, or in the industrial plant, can be safer than the man 
who is at the controls. If farm accidents are to be pre- 
vented — and they can be prevented — it will be done by the 
operators who accept a full measure of their responsibility. 

It is true that the designer, the manufacturer, the safety 
engineer can help; and they will help, but their combined 
efforts can be wiped out by a single careless act of the 
operator. 

It is said that "the best kind of a safety device is a care- 
ful operator." We ask you to be that kind of an operator. 

NATIONAL SAFETY COUNCIL 





JOHN DEERE 
QUALITY EQUIPMENT 

for your farming operations 



TRACTORS: Standard tread, general purpose, and orchard in 
sizes and types for every farm, crop, and purpose. 

PLOWS: All sizes and types, moldboard and disk, including inte- 
gral moldboard and disk types for John Deere general purpose 
tractors. Middlebreakers. Disk tillers in all sizes. Plow-sole ferti- 
lizer attachment for plows. 

LISTERS: One-, two-, and three-row for cotton, corn, and other 
crops. Integral middlebreakers and bedders and bedder planters for 
John Deere general purpose tractors. 

HARROWS: Single- and double-action disk types. Offset disk har- 
rows for orchard, vineyard, and cover-crop work. Spike-tooth har- 
rows, spring-tooth harrows, and spring-tooth weed destroyers. 
Stalk cutters. 

GRAIN DRILLS: Tractor- and horse-drawn grain drills in a size 
and type for every seeding job. Plain drills, fertilizer-grain drills, 
press drills, plow press drills, deep-furrow drills, and grass seed 
drills available. Adjustable-gate fluted force-feeds or double-run 
feeds. Choice of furrow openers. Fertilizer attachments available. 
Lime and fertilizer distributors. 

PLANTERS: One-, two-, and four-row for corn, cotton, peanuts, 
and other crops. Multi-row planters for beets, beans, and other 
narrow-row crops with or without fertilizer attachment. Planting 
and fertilizing attachments for cultivators. 

POTATO MACHINERY: One- and two-row planters, with or" 
without fertilizer attachment. Two-row tractor-drive diggers. One- 
row diggers— ground- and Uactor-drive. Hoe and hilling attach- 
ment. 

CULTIVATORS: One-, two-, four-, and six-row for flat-planted 
crops; one-, two-, and four-row for listed crops. Field and orchard 
cultivators with stiff or spring teeth. Alfalfa cultivators. Beet and 
bean cultivators. Rotary hoes. Rod weeders. 

DUSTERS: For cotton, vegetables, orchards, and groves. 

HAY MACHINERY: Enclosed-gear horse mowers, tractor-drawn 
mower, power-driven mowers. Side-delivery rakes, hay loaders, 
sweep rakes, sulky rakes. Power baler; automatic pick-up baler, 
hay choppers. 

HARVESTING MACHINERY: Combines and threshers. Grain 
binders, corn binders, rice binders for horses or tractor. Wind- 
rowers. Power-driven one- and two-row corn pickers. Ensilage 
harvesters; blowers. Beet lifters. Beet harvester. Beet loader. Bean 
harvesters. Peanut pullers. Cotton harvesters. 

GRAIN ELEVATORS: Portable, for ear corn and small grains, 
portable type for small grains only. Trench silo elevator. Grain 
mover. 

HAMMER AND FEED MILLS: Two types, five sizes to fit every 
need; also shelters for hand and power use. 

MANURE SPREADERS: Horse-drawn and tractor-drawn. Also 
lime-spreading attachment. Manure loader. 

FARM WAGONS: Rubber-tired gears for all-around hauling. 

MISCELLANEOUS: Deep tillage equipment, including panbreak- 
ers, subsoilers, and chisel cultivators. Land levelers. Tire pumps. 



JOHN DEERE 

GAVE TO THE WORLD THE STEEL PLOW 

IN 1837